[DeTomaso] Hehehe....

[Mad Dog Antenucci]

Roger that JB

"John Bentley (jab)" <jab at cisco.com> wrote:      I thought we also agreed on heavy weapons, Brazilian girls, and driving fast?
   
  JB
   
   

    
---------------------------------
  From: Mad Dog Antenucci [mailto:teampantera at yahoo.com] 
Sent: Tuesday, February 28, 2006 5:50 PM
To: John Bentley (jab); LiTtOFreAkYDeViL at aol.com; detomaso at realbig.com
Subject: RE: [DeTomaso] Hehehe....


  
  JB and I don't agree on anything except maybe D*ck's 3-point bars and his roll cages. hehehe
  MD

"John Bentley (jab)" <jab at cisco.com> wrote:
  I'm all for guys that like to do the job themselves, but you can't beat
one of D*ck's bars. Save yourself a lot of headache and just buy one
from him. They fit perfectly, come with everything you need, are fairly
priced, and you can get a removable third leg (which I have and
recommend) for added safety. You can come check out mine before you buy
if you like.

JB - seal of approval




-----Original Message-----
From: detomaso-bounces at realbig.com [mailto:detomaso-bounces at realbig.com]
On Behalf Of Mad Dog Antenucci
Sent: Tuesday, February 28, 2006 8:38 AM
To: LiTtOFreAkYDeViL at aol.com; detomaso at realbig.com
Subject: Re: [DeTomaso] Hehehe....

LARRY HEHEHE,

If you are running the 130 Average Group (165 top speed) and are
planning to fabricate and install your own roll bar make sure if you are
bolting it in you use the existing fire wall bolt holes and on the base
that you use a backing plate and you mount the bolts in the 'up'
position so that Tech can see you 'really' have secured the bar....a
couple of the Viper/Corvette/Porsche wieniers in attempting to NOT have
to drill holes into their precious factory race cars have actually
mocked up the bar, set in the car but never bolted it in or if the
bolted it in they never put a backing plate so now Tech wants to see
that your mounting base bolts and nuts are visable....again, check tech
rules and also check with John Bentley (JB) who isn't that far from you.
I know you have a budget and want to do the work yourself but Dick
Drenske I think has some roll bars already made up...contact D*ck if you
are interested.

MD

LiTtOFreAkYDeViL at aol.com wrote:
Okay okay mad dawg... thanks for the quick answers :) i'll spend some
time 
reading the SSCC tech rules since i just got done with all these school
test 
and etc... I really hope to get the pantera done on time!!!

A roll bar is just something that goes from one side (like my side next
to 
the door and seat).. up and over my head and down the other side
(passenger 
side) right? If that's all that's required.. i'll just bend my own
tubing... 
weld some plates on and bolt it to the car and run in 130 mph group
=P...

Oh i just ordered another electric water pump haha.. there goes another
500 
bucks...

And... i got my electric thermostat system... it has a freakin ECU with 
it!!! hahaha it even has an ambient temp sensor where it reads
information of the 
outside air temp to super super super accurately keep my temp within 3 
degrees of whatever "pill" i stick into the thermostat computer.. like
those rpm 
limiter pills... haha no wonder it cost more then my water pump =P..

Larry
_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at realbig.com
http://ftl.realbig.com/mailman/listinfo/detomaso

_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at realbig.com
http://ftl.realbig.com/mailman/listinfo/detomaso
_______________________________________________

Detomaso Forum Managed by POCA

Archive Search Engine Now Available at http://www.realbig.com/detomaso/

DeTomaso mailing list
DeTomaso at realbig.com
http://ftl.realbig.com/mailman/listinfo/detomaso